Series CA Auxiliary: 

  • Common for all modular protection devices: MCB’s and RCBO’s up to 63A, RCCB’s up to 100A and mains disconnect switches type ASTER (ASTM)
  • Can be coupled on both sides of MCB’s and modular switches type ASTM.
  • Version with golden contacts, available for low current as well as low voltage applications.
  • Stack-on left and right up to 4 CA units.
  • Permits the pass-through of busbars, pin & fork, top and bottom, just
  • changing the position of the base of the auxiliaries.
    Series CB Auxiliary: 

  • Common for all modular protection devices: MCB’s and RCBO’s up to 63A, RCCB’s up to 100A and mains disconnect switches type ASTER (ASTM).
  • Can be coupled on both sides of MCB’s and modular switches type ASTM.
  • Common for all modular protection devices: MCB’s and RCBO’s up to 63A, RCCB’s up to 100A.
  • Can be coupled on both sides of MCB’s and modular switches type ASTM.
  • This device has 2 change-over contacts, the upper one with changeable function (S/H).
  • Two versions: CB SH/HH-R to be coupled on the right side of the protection devices, CBSH/HH-L when assembled on the left side
  • No stack-on possibilities (only 1 auxiliary)
  • No busbar pass-through facilities
    Tele MP Motor Operator: 

  • The Tele MP allows to remotely open or close any MCB, RCCB, RCBO or modular switch by means of a push- button or any other automatic management processor (PLC).
  • Common device for all modular protection devices.
  • Can be coupled on both sides of MCB’s and modular switches, on the right hand side of RCCB’s and RCBO’s.
  • Stack-on left and right sides up to 4 modules. One of them can be coupled between the main device and the motor operator.
  • Can be locked in off position with a lock.
  • Manual operating is possible.
    Shunt Trip Tele L: 

  • The Tele L allows to remotely switch off any MCB, RCCB or RCBO by means of push-buttons or any other automatic management processor. A built-in contact in series with the coil prevents burn- out damage if the voltage remains.
  • Common device for all modular protection devices.
  • Can be coupled on both sides of MCB’s and modular switches, on the right side of RCCB’s and RCBO’s.
  • Permit the pass-through of busbars, pin & fork, at top or bottom terminals.
  • Stack-on left and right side up to 4 modules.
    Undervoltage Release Tele U:  

  • The Tele U releases the main MCB, RCCB, RCBO or modular switch in case the power supply drops below 0.5xUn. Time delay adjusting up to 300 ms.
  • Common device for all modular protection devices.
  • Can be coupled on both sides of MCB’s and modular switches, on the right side of RCCB’s and RCBO’s.
  • Permit the pass-through of busbars, pin & fork, at top or bottom terminals.
  • Stack-on left and right side up to 4 modules. 
    Panel Board Switch PBS:

  • The panel board switch PBS is a mechanical switch. When the panel frame releases the PBS switch, it will trip the protection devices (MCB’s or RCD’s). Consequently the distribution board will become isolated.
  • Common device for all modular protection devices.
  • Can be coupled on both sides of MCB’s and modular switches, on the right side of RCCB’s and RCBO’s.
  • Permit the pass-through of busbars, pin & fork, at top or bottom terminals.
  • Stack-on left and right side up to 4 modules.
    Add-on devices for MCB’s series Hti: 

  • Should be coupled on the right side of the MCB.
  • The shunt trip can be coupled on both sides of the MCB.

GE Power Protection offers you: Customer specific developments for all your applications and requirements, exclusively to meet your

Read More