Motor Control Center (MCC) – SEN Plus
SEN Plus new generation metal clad plug-in centers for each and every application.
The SEN Plus, modular range of equipment with rated currents up to 4000A, is part of the extensive range of Low Voltage Motor Control and Switchgear Equipment designed and manufactured by Power Protection.
The smart and simple design is fully type tested as per IEC 60439-1 and certified by an independent test laboratory (KEMA).
SEN Plus cubicles which comprise of Incomers, Starters, Feeders, and Distribution are designed for flush front or back to back arrangements. An equipment zone of (height x depth x width) 2200 x 600 x 600mm forms the basis of the cubicle design, to which a cable compartment can be added for either top or bottom cable access.
The construction of the SEN Plus range of equipment is fully compliant with the requirements of internal separations upto Form 4,with different options of cable termination from point of entry, using a common gland plate or individual gland plates and cable boxes for each outgoing functional unit.
The system is utilising a comprehensive range of Incomers with the new type fixed / withdrawable air circuit breakers series M-Pact , switched fuses series Fulos, isolators series Dilos and the new moulded case circuit breakers series Lancelot and fast exchangeable starter and feeder plug-in units .These functional units match with the new range of IEC 947 designed ,tested and rated industrial components to achieve complete system integration.
Finger proof shrouds and barriers prevent the possibility of any vertical busbar faults and provide the highest level of integrity at the heart of the design . Maximum safety level for the operator is ensured in case of reconfiguration of the equipment zone under energised conditions. The Main Distribution Panels and Motor Control Centers can be executed with a four or five phase busbar system up to 100kA-fault rating.
Why SEN Plus
Dust and waterproof: IP30 up to IP 54 as per IEC 529-1.
Flexible and compact: Final configuration can be determined just before shipment due to "add on concept".
Robust and secure: Good and easy access to all internal components. Vertical riser up to 80kAIcw/176Ipk.
Service: Customising (project specific requirements). OEM documentation in 3D arrangements.
Ready for the e-commerce take off: With the interactive CD-ROM you are composing and customising your own SEN Plus LV Switchgear and Motor Control Centers your self (design, calculator, general arrangement drawings and purchase order tool).
Smart & simple design to meet the need in lowest investment cost: Reduced "cycle times" and installation cost due to six sigma controlled processes.
Deliveries: Fast deliveries due to standardised concept.
SEN Plus Benefits
Rigid frame construction: Non welded zinc plated self-supporting construction made out of just 3 basic parts. No sharp edges.
For your safety: Short circuit proof and fatigue free self-aligning stabs secure high safety level during operation.
Fast and easy cabling: Through preconfigured copper links or terminal strips.
Durable surface protection: Shock and scratch resistant powder paint suitable for most applications including marine and tropical conditions.
Optimum accessibility and surveyability: 135 to 185 door opening angle. Control and indication.
SEK type tested
● Type tested to IEC 439, IEC 947 and DIN. VDE. 660 pt 500
● Arcproof design, fully insulated bus bars and risers to maximise safety
● Fully withdraweable incomers and feeders, including comprehensive safety interlocks to protect both person and plant
● HSEV Fuse Switch available in either BS/DIN fuses or MCCB configurations in up 32 modules per column
● Rated operational voltage: 690v
● Rated current: Up to 5000 A
● Rated Insulation voltage: 1000v
● Rated short time withstand current: Up to 100kA
● Rated impulse withstand current: Up to 220kA
● Protection class tot IEC 529: IP 20 to 54
● Height: 2200mm
● Depth: 600,800 & 1000 mm
● Width: 400,500,600,800,1000 mm
● Typical form of segregation: Form 1 to 4.7
● Structure: Aluzinc
Switch Board SEN Plus
● A Type Tested Assembly to IEC 61439-2 and IEC 60439-1,of robust, modular and compact construction
● Tested to comply with internal arc tests IEC/TR 61641
● Front access switchboard suitable for mounting against a wall providing front access for installation and maintenance of equipment
● Outgoing ways are available in fully withdrawable, plug-in or fixed versions for short circuit protection devices S.C.P.D.
● Rated operational voltage: 690V AC, 600V DC
● Rated current: Up to 7800 A
● Rated Insulation voltage: 1000 V
● Rated short time withstand current: Up to 100kA
● Rated impulse withstand current: Up to 220kA
● Ingress Protection class to IEC 529: IP 30 to 54
● Height: 2000, 2200mm
● Depth: 600, 800 & 1200mm
● Width: 400, 500, 600, 800, 1000, 1200 mm
● Typical form of separation: Form 1 to Form 4b
● Up to 40 x 100A TP FUSE SWITCHES Per column
● Colour RAL 7035 Epoxy-polyester paint
Switch board: Modula 630K
- A range of 12 enclosures equipped with a various range of functional units based on a module of 50 mm x 500 mm offering maximum possibilities to the panelboard builder
- Type tested distribution boards according to EN 60439-1
- Type tested energy distribution enclosure conforms to EN 60439-1
- LOVAG approved
- Manufactured in sheet steel and delivered in flat pack format
- Designed for 630A – 690V 40/60 Hz – 30 kA eff
- Easy wiring, due to the direct mounting of the functional units on the rear panel, used as mounting plate
- Cabinets are available as standard with protection degree IP41 and a high mechanical impact of IK08
- The application of the range makes it ideal for installation in electrical distribution systems in industrial and commercial markets
Modula 630K Features
- Delivered in kit form
- Form 1 and Form 2
- Easy wiring due to direct mounting of the functional units on the rear panel, used as a mounting plate
Protection Level
- Without door IP40 – IK07
- With plain door IP41 – IK08
- With transparent door IP41 – IK07
Materials Used
- Sheet steel coated with oven-baked epoxy paint
- Doors, side panels and roof: 1 mm thick
- Upper/bottom panels and bases: 2 mm thick
- Sendzimir zinc plated steel
- Rear panel: 1.5 mm thick
- Coupling kit: 2 mm thick
Colours
- RAL 7035: enclosure, doors and protective covers
- RAL 7024: bases
Switch Board – Modula Plus
Modula Plus
- A range of floor standing enclosures, busbar systems and functional units prepared to mount LV devices
- Offered in kit form, designed for low voltage distribution boards up to 4000A
- Cabinets are offered in 500mm & 700mm depths, in 650mm & 900mm widths. All cubicles are 2000mm high
- Type tested conforms to EN 60439-1
Modula Plus Features
- Form1, form2 & form3 (incoming section)
- Rated operational voltage Ue: 690V
- Rated insulation voltage Ui: 1000V
- Rated frequency: 50-60Hz
- Rated short circuit current Icw 70kA/1s
Standard application
- Air circuit breaker 400A-4000A, fixed & withdrawable
- Loadbreak switches up to 2500A, fixed, fused or fuseless
- MCCB’s up to 1600A, fixed or plug in
- Miniature circuit breakers
Protection Level
- With door IP55
- Without door IP30
Materials Used
- Cabinet – Sheet steel, 1mm
- External panel – Sheet steel, 2mm powder coated
- Doors – Sheet steel, 2mm powder coated
- Mounting plates – Sendzimir zinc plated steel
Colours
- External – RAL 7035
- Coverplates – RAL 7024
Motor Control Center (MCC) – SEV32 IntelligentMotor Control Centre – EPOS
- The ideal solution giving flexibility in design, protection and control
- Integration into a Fieldbus either through Modbus or Profibus
- EPOS makes engineering and modifying the design easier and faster
- Planned maintenance becomes a simpler task, reducing operating costs
- Modification becomes an easy operation, minimizing component change and time
- Rated operational voltage: 690v
- Rated current: Up to 5000A
- Rated insulation voltage: 1000v
- Rated short time withstand current: Up to 80kA
- Rated impulse withstand current: Up to 176kA
- Protection class to IEC 529: IP 20 to 54
- Height: 2200mm
- Depth: 600 & 1000mm
- Width: 400, 500, 600, 800 & 1000mm
- Typical form of segregation: Form 1 to 4.7
- Structure: Aluzinc
- Independent certification: KEMA
Motor Control Center (MCC) – SEV32 Motor Control Centre
- Type tested to IEC 439, IEC 947 and DIN. VDE. 660 pt 500
- Arcproof design, fully insulated bus bars and risers to maximise safety
- Fully withdraweable incomers and feeders, including comprehensive safety interlocks 2to protect both person and plant
- HSEV Fuse Switch available in either BS/DIN fuses or MCCB configurations in up 32 modules per column
- Compact design gives up to 32 x 11kW starters in a column all easy to cable, install and maintaining protection for the electrician from live connections and parts
- Fully withdrawable starters up to 280kW also Soft Starters & Variable Speed rives
- Designed for front access allowing direct mounting against a wall having total ease of use from the front for installation and maintenance