• 11151 Amman, Jordan

GE Products

  1. Home
  2. GE Products

Contactors for Capacitors Switching – Series CSCN

With built-in resistance to switch three phase capacitor banks

“CSCN” contactors incorporate a front block with three early-make auxiliary contacts together with 6 quick discharge resistors (two per phase) through which the capacitors are switched to the network, reducing the current peak.
Once the resistors have damped the current peak, the main contacts shortcircuit the resistors, carrying the uninterrupted current.
A few miliseconds later the early-make auxiliary contact closes to guarantee that all current flows through the main contacts.

Read More

Industrial contactors (Upto 450 kW) – Series CL and CK
  • IEC 947 standards compliant
  • Complete range:
    • 3 pole 4 – 450 kW at 400V, 9 – 105A AC3 rated
    • 4 pole 25 – 1250A AC1 rated
  • DIN rail mounting up to 55kW. Panel mounting across the whole range
  • A wide range of AC, DC and Electronic coil control voltages. DC operating limits 0.8…1.1 Us and operating limits 0.7…1.3 Us
  • Terminals in accordance with EN 50005, 50011 and 50012. Degree of protection IP20
  • Wide range of accessories:
    • Timers
    • Interface devices
    • Supressors RC, varistor and diode
    • Auxiliary contact blocks side mounting, also front mounting 4 -55kW
    • Mechanical/Electrical interlocks
    • Mechanical latch 4 -55kW.
  • Spare coils and contact kits available
  • Wide voltage tolerance DC coil control
  • Energy efficient low power coils
  • Quiet operation DC and Electronic coil control
Read More

Links Type ‘K’
  • For use in air on motor starting and general applications
  • Current ranges available:
    • 5A to 450A at 3.6kV
    • 50A to 350A at 7.2kV
    • 32a to 350A at 12kV
  • Meets dimensional and performance requirements of BS 2692 & IEC282
  • ASTA and/or KEMA certified short circuit testing
  • High current rating in single body dimensions
  • Low current and energy let-through under max fault conditions
  • Excellent performance under low over-current conditions
  • Ability to resist ageing under repeated starting conditions
Read More

Minicontactors (Upto 5.5 kW) – Series M

 

  • IEC 947 standards compliant
  • 3-pole: 2.2kW to 5.5kW – 380/415V – AC3, 6 to 12 A – AC3
  • Control circuit :AC, DC, low coil consumption (1.2 and 2W/24V). DC operating limits 0.8…1.1 Us and operating limits 0.7…1.3 Us
  • 4-pole: 20A AC1,Control circuit : AC, DC
  • Available in 3 different contact configurations
  • Terminal protection degree IP2X
  • Terminations: Screw, Ring Terminal, Fast-on – 2 x 2.8 mm (on request 1 x 6.3 mm) and Printed Circuit Board configurations
  • Terminals:
    • Numbered according to EN standards
    • Posidrive terminal screws
    • Mounting in line.
    • Terminal numbering in accordance with EN50012 and EN50005.
  • Coils:
    • Protected against overheating
    • Easily interchangeable
    • Spare parts
    • Wide Tolerance 0.7 – 1.3 x Us
  • Mounting:
    • 35 mm DIN-rail mounting or screw fixing
  • Accessories:
    • Front mounting auxiliary contact blocks.
    • Two and Four pole contact configurations.
    • Protection degree IP20.
    • Side mounting auxiliary contact blocks.
    • Single circuit contact blocks.
    • Common for AC or DC contactors.
    • Possible to mount up to 4 blocks in tandem.
    • Delay ON Electronic timer for front, side or DIN mounting timing range 0.5 – 60 sec and 0.2 – 24 sec.
Read More

Electronic Relays
  • DIN rail or panel mounting, single or multi voltage
  • Multiple application types:
    • Motor re-start
    • Earth leakage
    • Phase unbalance, failure and phase sequence
    • Voltage detection and protection
    • Current detection
    • Frequency control
    • Thermistor
    • Liquid level
    • Reactive power regulation
  • Multiple time and contact combinations
Read More

Plug-in Relays – Series PRC
  • Three basic mounting configurations, plug-in fast-on or solder mounting, printed circuit board solder mounting and plug-in 8, 11 or 14 pin relays
  • Contact combinations from 2 to 4 pole changeover
  • Control circuit voltages AC or DC from 6V to 240V
  • Relays are 6, 10 and 12 amp rated
  • Status indication either mechanical or LED or both
  • Sockets for 35mm DIN rail mounting
Read More

Auxiliary Contactors – Series M and RL
  • Two versions, mini 16A (Series M) and industrial 20A high performance (Series RL)
  • Three terminal connection methods, screw, fast-on and printed circuit board mounting
  • Multi contact combinations up to 10 pole
  • Interface relays 24V DC 1.2 and 2 watt coils
  • Complies with IEC 947-1 and other international standards
  • DIN rail or panel mounting
  • Fully protected from accidental contact with live parts IP20
  • Wide choice of AC and DC coil voltage options single and dual frequency

 

Read More

ASTAT S: Small soft starter with integral by-pass

ASTAT S is compact, easy to operate soft starter, designed for use with standard 3-phase squirrel cage motors. It provides an advanced method of reducing current during motor starting and stopping.



ASTAT S will start supplying a reduced voltage to the motor, increasing up to the rated voltage, so avoiding, high currents and generating soft starting and stopping.



The motor has to be able to start in a reduced voltage.



 

  • Solid soft starter for standard 3ph AC motors up to 30kW at 400V AC
  • Voltage ratings up to 600V
  • Two phase control with integral by-pass
  • Compact, small case
  • DIN rail mounting. Optional from 31A
  • Start and soft stop features
Read More